Home ›
Courses ›
Renewable Energy and Electronics Training Course
Renewable Energy and Electronics Training Course
Engineering, Energy & Technical Systems · 10 Days
Course Overview
Renewable energy installers are frequently strong on the mechanical side of installation but underprepared on the electronics that actually make a system work — and electronics technicians often lack exposure to renewable-specific system design.
This course closes that gap deliberately, pairing core electronics fundamentals (circuits, components, measurement and testing) with full renewable energy system design, sizing, installation, commissioning and troubleshooting — built around solar PV as the primary technology, with wind and hybrid systems covered as well.
The programme is lab-heavy throughout: participants build circuits, size real systems against sample loads, and complete hands-on installation and fault-finding exercises rather than working from theory alone.
Course Curriculum
1
Foundations of Electrical and Electronic Systems
- Basic electrical quantities: voltage, current, resistance, power
- Ohm's Law and circuit fundamentals
- AC vs DC systems
- Reading circuit diagrams and schematics
- Safety practices when working with electricity
- Overview of common electronic components
2
Core Electronic Components and Circuits
- Resistors, capacitors and inductors in practice
- Diodes, transistors and basic semiconductor behaviour
- Series and parallel circuit analysis
- Introduction to printed circuit boards
- Using breadboards for prototyping
- Practical circuit-building exercise
3
Measurement and Testing Instruments
- Using a multimeter for voltage, current and resistance
- Oscilloscope basics for waveform analysis
- Testing continuity, insulation and earthing
- Calibration and safe use of test equipment
- Interpreting test results
- Practical measurement lab session
4
Introduction to Renewable Energy Systems
- Overview of renewable energy technologies
- Solar, wind and hybrid system basics
- Renewable energy potential and site assessment
- Comparing renewable technologies for different applications
- Policy and market context for renewable energy
- Introduction to off-grid, grid-tied and hybrid configurations
5
Solar Photovoltaic (PV) Fundamentals
- How solar PV cells and modules work
- PV module specifications and datasheets
- Series and parallel module configuration
- Factors affecting PV system output
- Shading, orientation and tilt considerations
- Practical PV module testing
6
Solar System Design and Sizing
- Assessing energy demand and load profiles
- Sizing PV arrays to meet load requirements
- Selecting inverters, charge controllers and batteries
- Balance-of-system component selection
- Designing for off-grid vs grid-tied applications
- Practical sizing exercise using sample load data
7
Battery Storage and Hybrid Systems
- Battery technologies for renewable storage
- Battery sizing and depth-of-discharge considerations
- Charge controller types and selection
- Designing hybrid renewable-generator systems
- Battery management and safety
- Practical battery system exercise
8
Renewable Energy System Installation
- Site preparation and mounting structure installation
- Electrical wiring and connection best practice
- Installing inverters, controllers and batteries
- Earthing and lightning protection
- Installation safety protocols
- Practical installation lab exercise
9
Grid Connection and Inverter Technology
- Grid-tied inverter operation and synchronisation
- Net metering and feed-in considerations
- Power quality and harmonics basics
- Protection devices for grid-connected systems
- Islanding and anti-islanding protection
- Reviewing grid connection requirements
10
System Commissioning and Testing
- Pre-commissioning checks and inspections
- Commissioning procedures for solar systems
- Performance testing and verification
- Documentation for commissioned systems
- Handover procedures to clients
- Practical commissioning exercise
11
Troubleshooting and Maintenance
- Common faults in renewable energy systems
- Systematic fault-finding approach
- Preventive maintenance schedules
- Diagnosing electronic component failures
- Safety precautions during maintenance
- Practical troubleshooting lab session
12
Standards, Codes and Safety Compliance
- Overview of relevant electrical and renewable energy codes
- Health and safety requirements on installation sites
- Personal protective equipment for electrical work
- Risk assessment for renewable energy projects
- Environmental and disposal considerations
- Compliance documentation requirements
13
Capstone Project and System Design Package
- Defining a renewable energy project scenario
- Developing a complete system design
- Costing and specifying system components
- Presenting a design and installation plan
- Peer review and feedback session
- Capstone presentation and course wrap-up
Ready to Register for Renewable Energy and Electronics Training Course?
See full pricing, exact upcoming dates across Rwanda, Kenya, United Arab Emirates, and secure your seat online in minutes.
Book This Training →